History of the Atlantic Cable & Undersea Communications
Investigation of a cable sample found in a
Investigation of a cable sample found in a
Location of the find:
Object of the study:
Examination carried out: The samples were photographed as received and then with great difficulty cut up / open to reveal inner construction and component parts. Photographs were taken of various components (See images 1 to 10). The component parts were measured and a sketch (Fig 1, at end of article) was made indicating the parts and dimensions. The sketch also indicates initial thoughts as to the possible type of construction of the cable
Since work on the recovered samples continues, this report should be regarded as provisional. It is expected that further samples may be recovered which may give us additional information.
Description of the cable samples as found:
Images 1 and 2 show the longer sample.
There was heavy corrosion of the steel outer tapes which were bent and buckled probably due to being snagged by the farmer’s plough. It was evident, presumably as a result of the same snagging by the plough, that the sample had also been severely stretched.
General construction of the cable:
Description of each component:
The conductor is hard-drawn copper. The diameter is 3.28mm (0.130”) which is 10 gauge. Being hard drawn it would have 2 to 3 times the tensile strength of standard annealed copper. The surface was slightly corroded with traces of a whitish deposit.
The space between the conductor and the lead sheath appears to be mainly air, however, due to the cable being so badly twisted and stretched this space varied between zero and 15mm or more (see Image 10).
Various sections of cable were cut and at each point a number of material fragments either fell out of the space, or were found to be trapped in it. As well as sand and a few insects a number of small fragments of rather dirty transparent material were found.
Image 4 shows a collection of these fragments. The largest single piece is shown in image 5 and measures 18mm x 8mm x approx 1mm thick.
The lead sheath indicates that the cable was almost certainly designed for service underground and probably for direct burial.
Although badly distorted by being snagged and stretched by action of the farmer’s plough we can see that the overall internal diameter was approx 20mm and that the wall thickness was around 2mm.
The layer of tarred fibres over the lead sheath are typical of the type of bedding used on armoured cables from earliest times. The fibres are probably hemp and comprise a number of small bundles which are laid helically around the lead sheath (see image 8) and are impregnated with tar or similar compound. The main purpose of the bedding in this cable would seem to have been simple mechanical buffering between lead sheath and the tape armour to prevent abrasion and possible electrolytic action (?)
The two steel armour tapes are laid contra helically over the fibre bedding (see image 2, above).
In the UK steel tape armour such as we see here is not very often used. Most manufacturers and BS specifications go for steel wire armour (SWA) or steel wire braid (SWB).
Continental manufacturers, particularly the French use steel tape much more frequently. The original thought was that this MUST be a French cable but it now seems quite possible that it could have come from a UK or even US manufacturer.
Some further thoughts:
In the 1950’s and 60’s companies such as Phelps-Dodge in USA developed cables like “Styroflex” which used a helical membrane separator and it is sure that other manufacturers used discs of various types, and materials to try and achieve the same, low loss characteristics.
Various plastic materials were used including polystyrene, acrylics and also PTFE.
Just how this particular cable was constructed internally remains a mystery for the moment.
In particular why did the discs have several holes in them?
Copyright © 2007 Allan Green & FTL Design
Last revised: 25 July, 2007
Return to Atlantic Cable main page
Research Material Needed
The Atlantic Cable website is non-commercial, and its mission is to make available on line as much information as possible.
You can help - if you have cable material, old or new, please contact me. Cable samples, instruments, documents, brochures, souvenir books, photographs, family stories, all are valuable to researchers and historians.
If you have any cable-related items that you could photograph, copy, scan, loan, or sell, please email me: firstname.lastname@example.org